低成本、率、以工作質量保證產品質量

合力叉車故障的問題解決方案

來源：http://www.bimuyu888888.com/ 日期：2024-02-27 發布人：

◆氣門彈簧折斷

Valve spring broken

合力叉車的氣門彈簧折斷后，可將斷彈簧取下，把斷了的兩段反過來裝上，即可使用。也可找一片一毫米厚的鐵皮，剪成比彈簧直徑大1毫米的圓片，內部剪一圓孔，直徑小于彈簧直徑4毫米，外部邊緣每隔6毫米剪成4毫米長的裂口，剪好后每隔一片折疊一片，形成雙面彈簧座槽，再將彈簧調頭裝入鐵皮槽內即可使用。如彈簧斷成數節時，可將該缸的進、排氣門調整螺釘拆下，使氣門保持關閉狀態，讓該缸停止工作。

After the valve spring of the Heli forklift is broken, the broken spring can be removed and the two broken sections can be installed in reverse to use. You can also find a piece of one millimeter thick iron sheet and cut it into a circle that is 1 millimeter larger than the diameter of the spring. Cut a circular hole inside, with a diameter 4 millimeters smaller than the diameter of the spring. Cut the outer edge into 4 millimeter long cracks every 6 millimeters. After cutting, fold one piece every other to form a double-sided spring seat groove. Then turn the spring and install it into the iron sheet groove to use. If the spring breaks into several sections, the adjustment screws of the intake and exhaust valves of the cylinder can be removed to keep the valves closed and stop the cylinder from working.

◆叉車油箱損傷

◆ Forklift fuel tank damage

合力叉車在使用時，發現油箱漏油，可將漏油處擦干凈，用肥皂或泡泡糖涂在漏油處，暫時堵塞；用環氧樹脂膠粘劑修補，效果更好。

When the Heli forklift is in use and finds oil leakage in the fuel tank, it can be wiped clean and coated with soap or bubble gum to temporarily block the oil leakage; Repairing with epoxy resin adhesive yields better results.

油管破裂時可將破裂處擦干凈，涂上肥皂，用布條或膠布纏繞在油管破裂處，并用鐵絲捆緊，然后再涂上一層肥皂

When the oil pipe ruptures, the ruptured area can be wiped clean, coated with soap, wrapped with cloth or tape around the ruptured area, tied tightly with iron wire, and then coated with a layer of soap

◆叉車油管破裂

◆ Forklift oil pipe rupture

油管破裂時可將破裂處擦干凈，涂上肥皂，用布條或膠布纏繞在油管破裂處，并用鐵絲捆緊，然后再涂上一層肥皂。

When the oil pipe ruptures, the ruptured area can be wiped clean, coated with soap, wrapped with cloth or tape around the ruptured area, tied tightly with iron wire, and then coated with a layer of soap.

◆叉車油管折斷

◆ Forklift oil pipe breakage

合力叉車油管折斷時可找一根與油管直徑適應的膠皮或塑料管套接，如套接不夠緊密，兩端再用鐵絲捆緊，防止漏油?！揪唧w可參考《合力叉車操作守則》的相關內容】

When the oil pipe of the joint forklift is broken, a rubber or plastic pipe that is suitable for the diameter of the oil pipe can be used for sleeve connection. If the sleeve connection is not tight enough, both ends can be tied tightly with iron wire to prevent oil leakage. [For specific details, please refer to the relevant content of the "Heli Forklift Safety Operating Regulations".]

可根據砂眼大小，選用相應規格的電工用保險絲，用手錘輕輕將其砸入砂眼內，即可漏油、漏水

According to the size of the sand hole, corresponding specifications of electrician fuses can be selected, and gently smashed into the sand hole with a hammer to eliminate oil and water leakage

◆叉車缸蓋等部位出現砂眼而漏油、漏水

Sand holes appear in the cylinder head and other parts of the forklift, causing oil and water leakage

可根據砂眼大小，選用相應規格的電工用保險絲，用手錘輕輕將其砸入砂眼內，即可漏油、漏水。

According to the size of the sand hole, corresponding specifications of electrician fuses can be selected, and gently smashed into the sand hole with a hammer to eliminate oil and water leakage.

◆油管接頭漏油

Oil leakage from oil pipe joints

合力叉車使用時，如發動機油管接頭漏油，多是油管喇叭口與油管螺母不密封所致，可用棉紗纏繞于喇叭下緣，再將油管螺母與油管接頭擰緊；還可將泡泡糖或麥芽糖嚼成糊狀，涂在油管螺母座口，待其干凝后起密封作用，也可將人造革或皮褲帶剪成型或放入孔中砸成型，安上即可，還可用一截塑料管剪開成型安上。

When using a hybrid forklift, if the engine oil pipe joint leaks oil, it is often caused by the unsealing of the oil pipe horn and oil pipe nut. Cotton yarn can be wrapped around the lower edge of the horn, and then the oil pipe nut and oil pipe joint can be tightened; You can also chew bubble gum or maltose into a paste and apply it to the nut seat of the oil pipe. After it dries and solidifies, it will act as a seal. You can also cut or smash the artificial leather or leather pants into shape or put them into holes, and then attach them. You can also cut a piece of plastic pipe to form and attach them.